Re: msa 2050 active/active setup on RHEL 6
Not exactly sure about your configuration, but keep in mind the MSA works with ALUA, this means the server always talks to the owner controller of a LUN, not to the "non-optimized" partner "standby"...
View ArticleRe: msa 2050 active/active setup on RHEL 6
I've two paths to controller A and two paths to B. A Pool has the LUN so I woul like to have at least two active connections, to A and not only one?!/etc/multipath.conf: # multipath.conf written by...
View ArticleRe: msa 2050 active/active setup on RHEL 6
>> A Pool has the LUN so I woul like to have at least two active connections, to A and not only one?! This would be correct.
View ArticleRe: msa 2050 active/active setup on RHEL 6
wrote: This would be correct.and that is my my problem - only one path is active!
View ArticleRe: msa 2050 active/active setup on RHEL 6
You should probably have a device specific section in your multipath.conf,
View ArticleRe: msa 2050 active/active setup on RHEL 6
yes, thats why I'm posting here my question.
View ArticleRe: msa 2050 active/active setup on RHEL 6
This may help: https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-c01388344 basically the MSA2000 config applies.
View ArticleRe: hpasmcli command is not working .
Dear All,I finally succeed to make the command "hplog -v " to work, that's why I am sharing with the community my experience.We have a dataserver with ~300 servers family HP Proliant most are BL460c...
View ArticleRe: Cent OS 7 and HPE drivers
Since the last HP-HEALTH version 10.70 that you can find under: https://downloads.linux.hpe.com/SDR/repo/spp/2018.03.0/packages/You can download the two following packages:...
View ArticleRe: msa 2050 active/active setup on RHEL 6
It has used the default path selector which is "round-robin" unless modified in the configuration file. You could add 'path_selector' to the one that you wanted to be into defaults section and then...
View ArticleRe: msa 2050 active/active setup on RHEL 6
Finally I changed my multipath.con defaults to: defaults { user_friendly_names yes polling_interval 10 path_selector "round-robin 0" path_grouping_policy group_by_prio prio alua path_checker tur...
View Articleno acceptable C compiler found in $PATH
I am trying to install Wireshark in Kubuntu,When I type ./configureI get the following errors "no acceptable C compiler found in $PATH"What is the fix? root@amd-ThinkCentre-M93p:/home/amd# cd...
View ArticleRe: no acceptable C compiler found in $PATH
> I get the following errors "no acceptable C compiler found in $PATH"> What is the fix? The usual fix might be to install a C compiler.> checking for gcc... no GCC would seem to be what...
View ArticleRe: no acceptable C compiler found in $PATH
Install gcc, or better yet use apt to install the wireshark binary compiled for your system unless you have a specific need to install from source
View ArticleRe: no acceptable C compiler found in $PATH
How do I make it so the GCC main executable is in my path?Your help much appreciated.
View ArticleRe: no acceptable C compiler found in $PATH
> How do I make it so the GCC main executable is in my path? _If_ you have installed GCC, then I'd expect it to be in some commonplace (like,say, "/usr/bin", "/usr/local/bin", ...), so you...
View ArticleCentos 7 install issue with HP ProLiant DL380p Gen8
Some relevant info8 x 1 TB drives in a raid 5 (hardware raid)This system currenlty works on Centos 6.4 and has the OS installedHowever when trying to setup a new install using Centos 7, apparenlty...
View ArticleRe: Centos 7 install issue with HP ProLiant DL380p Gen8
On Gen8 servers, there is no 'Legacy boot mode' as the system firmware is BIOS and not UEFI.How many logical drives were defined on the system when running CentOS 6.4? Most OS's using MBR (BIOS) drive...
View ArticleRe: Centos 7 install issue with HP ProLiant DL380p Gen8
Yes I think that may be part of the issue, however as far as I can tell whoever installed CentOS 6 on here set it up with 1 array using all 8 x 1 TB drives, so based on what I see in the bios therre is...
View ArticleInstallation of debian 9 on DL20 Gen9
Hi,I have installed debian 9.3 on DL20 Gen9, in legacy mode i have changed the controler to AHCI SATA mode. When Debian 9.3 start, what happen is that the screen of the system appear like on the...
View Article